Martel-electronics MC1000 Bedienungsanleitung

MC1000 Multi-FunctionCalibrator

ending setpoint location. Example: ifyou have all 9 setpoints stored butonly want to step through the first 3then enter “3” for this question.c. The n

9

103. Connection Diagrams &InstructionsA. Measuring High Voltage AC or DC1. Select the Voltage Input Mode. Use the“Range” key to select either AC o

11C. Measuring Current1. Select the mA input mode. Note: To powerthe loop while reading current, select the“mAPW” mode.2. Connect the device under tes

12E. Simulating CurrentThe MC1000 can act as a two-wire transmitterand control a 4-20mA loop from the externalpower supply for that loop.1. Select the

13I. Measuring Resistance (RTDs)When measuring resistance (ohms) there are 3choices when using the MC1000; 2-wire, 3-wire, and 4-wire. While 4-wire o

142. Make sure the MC1000 is in the Input Mode(Note: that it will indicate 2, 3, or 4W in theupper left corner of the LCD).To set the desired wire con

154. Serial CommunicationsThe MC1000 calibrator is equipped with a RS-232 serial communications port, which is locat-ed on the top of the case. Note:

The MC1000 calibrator can be used with virtually any terminal emulation software. (i.e.Procomm or HyperTerminal) When connected properly, data will b

(D.) Stop Bits: 1(E.) Flow Control: Xon/XoffClick OK box to accept these entries. 8. Hook up the MC1000 calibrator to the PC uti-lizing the special

Table of Contents1. Introduction1.1 Customer Service . . . . . . . . . . . . . . . .11.2 Standard Equipment . . . . . . . . . . . . . .11.3 Safety In

Serial Input DescriptionA mA measurement a mA source I mA loopi mA 2W SimV Volts measurementv Volts sourceM mV measurementm mV sourceE HVA

19Serial Input Selection Entry DescriptionS No. T/C Type RTD Type6 S Pt500 (385)7 B Pt1000 (385)8 L NI1209 U YSIA N OHMSBmV® Microsoft, Windows, Windo

206. SpecificationsPressure Module Dependent. Operates with Fluke 700 Series Ranges: Modules T/C Ranges: J, K, T, E, R, S, N, B, L, U including – 10 t

21Range & AccuracyRange Min Max Accuracy (% of reading ±counts)V Read (low) 0.000 20.000 0.015% ±2VDC Read (high) 0.0 250.0 0.05% ±2VAC Read (high

Thermocouple Read and Source (All errors included) (cont.)Range Min Max Accuracy L Thermocouple -200 0.0 0.45°C0.0 900.0 0.4°CU Thermocouple -200 0.0

7. WarrantyMartel Electronics Corporation warrants allproducts against material defects and work-manship for a period of twelve (12) monthsafter the d

Rev G 10/08 0219041Corporate Office:www.martelcorp.come-mail: [email protected]: (603) 434-1433 800-821-0023 Fax: (603) 434-1653

1MC-1000 1. IntroductionThe MC1000 is designed to be a versatile, easyto use multi-function calibrator with a simpleuser interface. The following inst

21.3 Safety information Symbols UsedThe following table lists the InternationalElectrical Symbols. Some or all of these sym-bols may be used on the in

3OffOnCanadian Standards AssociationThe following definitions apply to the terms“Warning” and “Caution”.• “Warning” identifies conditions and actionst

4• Remove test leads from the calibrator beforeyou open the battery door.• Inspect the test leads for damaged insulationor exposed metal. Check test l

5CautionTo avoid possible damage to calibrator orto equipment under test:• Disconnect the power and discharge all high-voltage capacitors before testi

2. Quick Start InstructionsA. Key FunctionsKey FunctionInput/Output Toggles the function selectedfrom measurement mode tosource mode.V/mA/Hz Selects b

and acts as a second functionkey to all keys that have anassociated second function.Features such as setpoints,°F/°C, backlight and externalpressure m